#Amx to pwm converter serial#
#Amx to pwm converter full#

#Amx to pwm converter full#

Sets RGB light with ID=1 to cyan color, full saturation, 50% brithtness. Simulates short press of push button with ID=1. Sets multi-value switch with ID=1 to value 3. Response: Set point | Temperature | Humidity Sets thermostat with ID=1 to no error, set point 24.5✬ Please note that already added devices are shadowed.Īfter adding device it is displayed in list of devices for Integration protocol interface:Ĭlick on device to display information about it, change automatically generated device ID, or delete device from exposed devices. Then use Add device to add your devices in the exposed devices:Ĭhoose device from list of offered devices.

#Amx to pwm converter serial#

Set all serial line parameters as required by connected client. Set unique Interface ID for each interface if you want to use address mode.Ĭhoose terminal for communication and fill communication parameters for RS485.

From offered interfaces choose one of Integration protocol RS485, Integration protocol TCP or Integration protocol UDP:Īfter adding interface according to type fill other parameters. !2:ID:11,Type:Blind,Name:Virtual blind,Status:OKįor exposing devices in Integration protocol first go to Expose devices and choose Add new interface. !2:ID:8,Type:Variable,Name:Sun azimuth,Status:OK !2:ID:7,Type:Variable,Name:KNXVariable,Status:OK !2:ID:6,Type:Thermostat,Name:Thermostat 1,Status:OK !2:ID:5,Type:Dimmer,Name:Analog output,Status:OK !2:ID:4,Type:PushButton,Name:Push button,Status:OK !2:ID:3,Type:MultiValueSwitch,Name:Heating & Cooling,Status:OK !2:ID:2,Type:Switch,Name:Ex Switch,Status:OK Only interface with correct address will answer - incorrect addressing can not be recognized by answer.Įxample of address mode request with command !2:LIST: Each answer line is than also proceeded with the same header. Address headers is sequence!InterfaceID: where InterfaceID is set in interface configuration. In this mode the address header proceeding the command itself. When unique interface ID is set, than it is possible to use all command in address mode. In RS485 lines where it is required SET and ACTION commands we suggest to use periodic pooling through command GET instead of automatic monitoring. There is possible to switch it on also on RS485 line in systems where no SET command or ACTION commands will be used - this means only in monitoring systems. So we suggest to use this command only in full duplex lines / like RS232 or RS422. Please note that when used on RS485 line there can be possible conflict on the bus which resolve to data mismatch. Information are send in same format as response to command GET. There are three actions number for blinds:ġ adjust level from actual position +-valueĢ adjust blind angle from actual position +-valueĮxample output of command ACTION 137 1 -20:Ĭommand PUSHALL will enable sending of all devices changes. ID:137,DeviceStatus:0,BlindsLevel:35,BlindsSlope:80Ĭommand action will execute action on device ID with send value. For devices with more than one value all values should follow - for example blind require both parameters to be send - new level and new angle.Įxample of output of command SET 137 0 35 80 with and then without header information: First it is device ID, then new device status to be set and then at least one value to be set. ID:137,DeviceStatus:0,BlindsLevel:41,BlindsSlope:41Ĭommand SET need at least three parameters. It returns device status and values as numbers. ID:143,Type:Variable,Name:Sun azimuth,Status:OKĬommand GET need one parameter - device ID. ID:145,Type:Variable,Name:KNXVariable,Status:OK

ID:68,Type:Thermostat,Name:Thermostat 1,Status:UnknownError ID:242,Type:Dimmer,Name:Analog output,Status:OK

ID:205,Type:PushButton,Name:Push button,Status:OK ID:2,Type:MultiValueSwitch,Name:Heating & Cooling,Status:OK ID:51,Type:Switch,Name:Ex Switch,Status:OK ID:137,Type:Blind,Name:Virtual blind,Status:OK HEADER OFF will switch off header information.Ĭommand LIST displays all exposed devices.ĭevice Type is text description of device type (Blind, Switch. HEADER ON will switch on header information. HEADER without parameters send information about actual switch state. In case header is off it are send only data. If header is ON there are send description information together with data. PUSHALL switch push all devices change on or off.Ĭommand HEADER switch between two possible data output. SET set device with ID status ST and values VAL1 to VALN.ĪCTION Perform on device with ID action number NUM with value VAL. HEADER switch header information on or off. HELP, LIST, GET, SET, ACTION, HEADER, AUTOSENDĮvery command must be terminated with CRLF (0x0D 0x0A, ) characters.Ĭommand HELP will display basic information about supported commands. This enables other systems to get information and control TapHome devices. TapHome system is able to integrate with other systems through simple ASCII integration protocol.